Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 262 / 432

background image

3.

Set the parking brake switch (4) to ON position (A) and ap-
ply the parking brake.

REMARK

Applying the parking brake automatically sets the trans-
mission to NEUTRAL.

4.

After the parking brake pilot lamp lights up, release the
brake pedal gradually.

TRANSMISSION CUT-OFF FUNCTION

Turn the transmission cut-off switch ON.
The transmission cut-off pilot lamp lights up on the monitor and
the following transmission cut-off function works.
When the brake pedal is depressed, the brakes are actuated
and the transmission is returned to NEUTRAL at the adjusted
brake pedal depressing position.
Position (a): Each time it is pressed, the transmission cut-off
function switches between ON and OFF.
When you release your hand, the switch returns automatically
to its original position.
When the brake pedal is depressed, the brakes are actuated and the transmission is returned to NEUTRAL at
the adjusted brake pedal depressing position.

REMARK

• For adjustment of the depressing position of the brake pedal, see “METHOD FOR ADJUSTING TRANS-

MISSION CUT-OFF POSITION (3-199)”.

• Adjust the depressing position of the brake pedal high or low depending on the type of work described be-

low.

• When performing piling-up operation, set the transmis-

sion cut-off (transmission in NEUTRAL) position of the
brake pedal to a lower position. In this setting, the
power from the transmission is cut with the brake ex-
erting ample braking force, so this prevents the ma-
chine from slipping down.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-198

«
...
260
261
262
263
264
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Takeuchi Страницы: 213

Бренд: Hitachi Страницы: 51

Бренд: Ballymore Страницы: 16

Бренд: Toro Страницы: 40

Бренд: Grizzly Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды