Komatsu WA380-8 страница 204 Скачать руководство пользователя | Manualshive

Страница: 204 / 432

background image

2.

Operate the menu switch to select “Aftertreatment Devices
Regeneration” menu (C) and display “Aftertreatment Devi-
ces Regeneration” screen.

3.

Select Regeneration Disable and press ENTER switch.
The regeneration function is disabled and the regeneration
is not performed.

REMARK

• When the regeneration is disabled, aftertreatment devices

regeneration disable pilot lamp (1) is displayed with hatch
on the standard screen.

• The setting of the regeneration disable is canceled by turn-

ing starting switch to OFF position. When the automatic re-
generation needs to be kept disabled, perform the above
procedure each time you start the engine.

• During the regeneration to protect the system, even if the

regeneration  disable  is  set,  aftertreatment  devices  regen-
eration  pilot  lamp  (2)  may  light  up,  but  this  does  not  indi-
cate  abnormality.  Also,  during  the  regeneration  to  protect
the system, the regeneration disable cannot be operated.

• When the regeneration is performed to protect the system,

the exhaust temperature is lower than that of when the re-
generation is performed to burn soot, and is almost the
same level as the normal exhaust gas temperature.

WHILE REGENERATION IS BEING PERFORMED: STOPPING REGENERATION

(When the aftertreatment devices regeneration display is lit on the standard screen)
1.

When the menu switch is pressed on the standard screen,
“Aftertreatment Devices Regeneration” screen is dis-
played.

EXPLANATION OF COMPONENTS

OPERATION

3-140

«
...
202
203
204
205
206
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: ICC Страницы: 37

Бренд: Ametek Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды