Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 203 / 432

background image

REMARK

• The progress of the manual stationary regeneration

performed when soot is accumulated can be checked
by the number of lighting lamps of soot accumulation
level (2). The manual stationary regeneration starts at
soot accumulation level “4” or higher and finishes
when all the level lamps go out.

• The manual stationary regeneration for protection of

the system during cold season may start even when
the soot accumulation level is “0” to “3”. In this case,
the soot accumulation level may not decrease, but this
is not a failure. The progress is not displayed on the
monitor during this regeneration. It is completed in ap-
proximately 10 minutes.

• If the accelerator pedal or directional lever is operated,

or  the  parking  brake  is  released  during  the  manual
stationary  regeneration,  the  regeneration  is  stopped
automatically.  Release  your  foot  from  the  accelerator
pedal, turn the directional lever to NEUTRAL position
(N), apply the parking brake, and then repeat the pro-
cedure from step 5.

• When the machine needs to be moved during the

manual stationary regeneration, stop the regeneration
temporarily and move the machine, referring to the af-
tertreatment  devices  regeneration  disable  and  cancel
of  regeneration  disable  procedures  described  in  the
following.
When  restarting  the  manual  stationary  regeneration,
secure  the  safety  of  the  machine  and  around  it,  then
cancel the regeneration disable.

8.

After the manual stationary regeneration is completed, the screen automatically returns to the standard
screen.

PROCEDURE FOR AFTERTREATMENT DEVICES REGENERATION DISABLE
SETTING

If there is combustible material around the machine and the active regeneration that increases the exhaust tem-
perature must not be performed, the automatic active aftertreatment devices regeneration can be disabled.
Also, the regeneration in progress can be stopped.

NOTICE
Even if the regeneration is disabled, KDPF soot accumula-
tion caution lamp (1) lights up if soot is accumulated and
the manual stationary regeneration is required.
If KDPF soot accumulation caution lamp lights up, move
the machine to a safe place and perform manual stationary
regeneration.
If the operation is continued without performing the man-
ual stationary regeneration, it may cause the failure of
KDPF or the engine.

WHILE REGENERATION IS NOT BEING PERFORMED: SETTING FOR REGENER-
ATION DISABLE

(When the aftertreatment devices regeneration is not displayed on the standard screen)
1.

Press the menu switch on the standard screen.

OPERATION

EXPLANATION OF COMPONENTS

3-139

«
...
201
202
203
204
205
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Allied Страницы: 38

Бренд: Toro Страницы: 34

Бренд: Kubota Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды