manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu WA380-8 Скачать руководство пользователя страница 169

TRANSMISSION SHIFT MODE SELECTOR SWITCH

The  transmission  shift  mode  selector  switch  is  used  to  switch
the transmission between the auto shift and manual, and also
change the shift point when the auto shift is selected.
When  this  switch  is  at  (B)  or  (C)  position,  the  transmission  is
set in the auto shift mode and the auto shift pilot lamp lights up
on the machine monitor. Normally, set it to auto shift mode.
Position  (A):  The  manual  shift  mode  is  set  and  the  machine

travels at the gear speed displayed on the shift indicator.

Position (B):Travel speed when shifted up is low (level ground,

normal travel)

Position (C):Travel speed when shifted up is high (uphill, full throttle travel)
When most of the machine operations is done on a level ground, selecting position (B) allows shifting up the
gear at a low engine speed, and it enables to reduce the fuel consumption.

REMARK

For detail of the manual shift, see “MANUAL SHIFT (3-108)”.
For detail of the auto shift, see “AUTOMATIC SHIFT (3-108)”.
However, when E mode is selected to reduce the fuel consumption, the shift point remains unchanged whichev-
er you may choose, (B) or (C).
Lamp for the transmission shift mode selector switch lights up when position of (A) or (C) is selected.
Lamp does not light up when position (B) is selected.

TORQUE CONVERTER LOCKUP SWITCH

The torque converter lockup switch is used to turn the torque converter lockup function ON and OFF.
Each time position (A) of the switch is pressed, the function switches between ON and OFF.
If you release your hand from the switch, it automatically returns to its original position.
For setting when the starting key is in ON position, see “LOCK-
UP FUNCTION SETTING WHEN KEY IS ON (3-73)”.

ON

The lockup operates according to the travel speed and working
condition.

OFF

The lockup function is disabled.
For  detail,  see  “HANDLE  TORQUE  CONVERTER  LOCKUP
(3-202)”.

REMARK

Usually, select ON mode to work with less fuel consumption.

DIRECTIONAL SELECTOR ENABLE SWITCH ON R.H. SWITCH PANEL

(if equipped)
The directional selector enable switch on R.H. switch panel is
used to enable the directional selector switch.
The basic operation is as follows.
Position (A): Directional selector switch is enabled.
Position (B): Directional selector switch is disabled.
When  setting  the  directional  selector  enable  switch  on  R.H.
switch panel to position (A), set the directional lever and the di-
rectional selector switch to the NEUTRAL position.

OPERATION

EXPLANATION OF COMPONENTS

3-105

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды