manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu WA380-8 Скачать руководство пользователя страница 163

AUTO-GREASING SWITCH

You can start the auto-greasing system with the auto-greasing
switch.
Position (A): You can perform 1 cycle of greasing regardless of
the elapsed time.
If  you  release  your  hand  from  the  switch,  it  automatically  re-
turns to its original position.

PARKING BRAKE SWITCH

k

k

 WARNING

When parking or leaving the machine, always apply the parking brake.
Keep  depressing  the  brake  pedal  until  the  parking  brake  pilot  lamp  lights  up  on  the  machine  monitor
even when the parking brake switch has been turned ON.
 

NOTICE

• Do not use the parking brake switch during traveling except for an emergency. The parking brake

may be damaged and a serious accident may result. Stop the machine, and then apply the parking
brake.

• If the parking brake was used as a secondary brake when the machine was traveling at high speed,

ask your Komatsu distributor for inspection of the parking brake system.

The parking brake switch is used to apply the parking brake.
Position (A): ON (actuated); The parking brake is applied, and

the parking brake pilot lamp lights up on the monitor.

Position (B): OFF (released); The parking brake is released.

REMARK

• When  the  parking  brake  has  been  applied,  the  machine

does not move even if the directional lever is operated.

• When the directional lever is shifted to F (forward) or R (re-

verse) position while the parking brake is applied, the cen-
tralized  warning  lamp  lights  up  and  the  alarm  buzzer
sounds.

• Start  the  engine  after  turning  the  parking  brake  switch  to

ON position.

OPERATION

EXPLANATION OF COMPONENTS

3-99

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды