Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 126 / 432

background image

2.

Select “ON” or “OFF”, then press ENTER switch (1).

“ON”

Displays the operational advice on the end screen.

“OFF”

Does not display the operational advice on the end screen.
To cancel, press RETURN switch (2).
The default is “ON”.

REMARK

In  the  “Operational  Advice”  section  indicated  on  the  end
screen,  the  advice  to  the  ECO  guidance  that  was  displayed
most  frequently  after  the  starting  switch  is  turned  to  ON  posi-
tion  is  indicated.  Accordingly,  the  operational  advice  indicated
on the end screen may be different from the “Operational Ad-
vice” indicated on “ECO GUIDANCE RECORD (3-54)”.

MACHINE SETTING AND INFORMATION

In each item of “Machine Setting and Information” menu (B),
setting and information of the machine are checked or
changed.

SELECTION OF E light MODE OR E MODE
Function of E light mode/E mode

• E mode (Economy mode): The engine output is set lower than in P mode (Power mode) and this mode im-

proves the fuel efficiency.

• E light mode: The engine output during digging is set lower than in E mode and this mode improves the fuel

efficiency further. (The engine output except for during digging is the same as in the E mode.)
This mode produces more effects when digging the objects of lighter specific gravity.
Also, the fuel efficiency can be improved if the time for digging is shortened.

The mode which is selected here is only effective when the power mode is other than P mode.

E light mode/E mode

The mode can be changed according to the following procedure.

EXPLANATION OF COMPONENTS

OPERATION

3-62

«
...
124
125
126
127
128
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Takeuchi Страницы: 17

Бренд: Terex Страницы: 85

Бренд: Hitachi Страницы: 51

Бренд: Toro Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды