Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 116 / 432

background image

(4) RETURN switch

Cancels a selection or changes, and returns to the previous screen or the standard screen.

REMARK

• If no switch is operated for 30 seconds on the user menu screen, the screen automatically returns to the

previous screen or the standard screen.

• The user menu screen is displayed only while the machine is stopped completely.
• If the machine travels while the user menu screen is displayed, the screen automatically returns to the

standard screen.

REMARK

The default tab when the standard screen is changed to the user menu screen varies with the machine condi-
tion.
1. SCR event occurs → “SCR Information”
2. KDPF event occurs → “Aftertreatment Devices Regeneration”
3. Hydraulic fan is rotating in reverse → “Machine Setting and Information”
4. Maintenance caution occurs → “Maintenance”
5. Message is not read yet → Message display
6. Other than 1 to 5 → “Energy Saving Guidance”
* If multiple conditions are established simultaneously, the above priority is given.

ENERGY SAVING GUIDANCE

Each item of “Energy Saving Guidance” menu (A) is used for
displaying and setting the notification relevant to energy saving.

• “Operation Records”
• “Eco Guidance Records”
• “Average Fuel Consumption Record”
• “Configurations”

OPERATING RECORD

The “Operation Records” screen displays the following informa-
tion on a daily basis or during the split measurement period.

• “Working Hours (Engine On)”: The time during which the

engine is running

• “Average Fuel Consumption”: Average of the fuel con-

sumed while the engine is running

• “Actual Working Hours”: The time spent for traveling, oper-

ation of work equipment and operation of accelerator

• “Ave Fuel Consumption (Actual Working)”: Average of the

fuel consumed during actual work

• “Fuel Consumption”: The amount of fuel consumed
• “Idling Hours”: The time during which the machine is stop-

ped, and the work equipment and accelerator are not oper-
ated

• “Economy Mode Ratio”: Percentage of E mode operation

in the engine-running hours

Select “ECO Guidance Records” from “Energy Saving Guid-
ance” menu screen, then press ENTER switch (1).

EXPLANATION OF COMPONENTS

OPERATION

3-52

«
...
114
115
116
117
118
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Baoli Страницы: 112

Бренд: Land Pride Страницы: 34

Бренд: AVANT Страницы: 148

Solar Gard Computer Cut

Бренд: SAINT-GOBAIN Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды