Komatsu WA380-8 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 432

Komatsu WA380-8 Скачать руководство пользователя страница 111

The function of each switch varies depending on the screen of the machine monitor.

(1) UP switch
(2) Air conditioner switches, numeric keypad
(3) Menu switch
(4) ENTER switch

(5) RETURN switch
(6) DOWN switch
(7) Guidance icon

MENU SWITCH

When this switch is pressed on the standard screen, the follow-
ing  user  menu  screen  is  displayed.  The  user  menu  screen  is
not displayed during traveling.
For the user menu, see “USER MENU (3-49)”.
When normal: Displays the ECO guidance menu screen.
When  KDPF  soot  accumulation  caution  lamp  lights  up:  Dis-
plays the “Aftertreatment Devices Regeneration” menu screen.
When maintenance caution lamp lights up: Displays the “Main-
tenance” menu screen.
When  fan  reverse  pilot  lamp  lights  up:  Displays  the  “Machine
Setting and Information” menu screen.
When message pilot lamp lights up: Displays the Message display menu screen.
When the menu switch is pressed on the user menu screen, the menu screen changes.

ENTER SWITCH

Pressing ENTER switch on the user menu screen decides any
selection and changes, and proceeds to the next screen.
When ENTER switch is pressed on the standard screen with a
warning message displayed, the “Current Abnormality” screen
is displayed.
For the “Current Abnormality” screen, see “CURRENT AB-
NORMALITY LIST DISPLAY (3-17)”.

OPERATION

EXPLANATION OF COMPONENTS

3-47

«
...
109
110
111
112
113
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды