Komatsu PW98MR-10 Скачать руководство пользователя страница 297 | Manualshive

Страница: 297 / 446

Komatsu PW98MR-10 Скачать руководство пользователя страница 297

METHOD FOR REMOVING BATTERY

1.

Open engine hood (1).

2.

Lock the engine hood securely with the hood support lever.

3.

Open battery inspection cover (2).

4.

Lock the battery inspection cover securely with the cover
support lever.

5.

Remove wing nuts (3) (2 places).

6.

Remove rubber cover (4).

7.

Remove cable (5) on the negative (-) terminal side (ground
side) first.

8.

Remove cable (6) on the positive (+) terminal side and
connecting cable (7).

9.

Remove mounting bolts (8) (4 places).

10. Remove mounting hardware (9).
11. Take the battery out of the machine.

METHOD FOR INSTALLING BATTERY

NOTICE
After securing the battery, check that it does not move.
If it moves, tighten it again securely.

1.

Place the battery in the specified position.

2.

Fix the battery firmly by using mounting hardware (9) and
mounting bolts (8).
Allowable tightening torque of mounting bolt: 9.8 to
19.6 Nm {1 to 2 kgm, 7.2 to 14.5 lbft}

3.

Install cable (6) on the positive (+) terminal side.

4.

Connect connecting cable (7) to the positive (+) terminal
side first.

5.

Connect cable (5) on the negative (-) terminal side (ground
side).

6.

Install rubber cover (4) with wing nuts (3).

NOTICE

• For prevention of a fire, install rubber cover (4)

carefully so that it will not roll up.

• If rubber cover (4) rolls up and blocks the fuel

cooler, the fuel may overheat. Take care to insert
rubber cover (4) under fuel cooler (10).

7.

Insert rubber cover (4) under fuel cooler (10).

8.

Remove the cover support lever from the hole of the bot-
tom cover and insert it into the mounting hole of battery in-
spection cover (2).

9.

Close battery inspection cover (2).

10. Remove the hood support lever and securely fix it to the lever lock.
11. Close engine hood (1).

OPERATION

TROUBLES AND ACTIONS

3-229

WENAM00061

«
...
295
296
297
298
299
...
»

Содержание PW98MR-10































































































































































































































































































































































































































































Отзывы:

Нет отзывов