manualshive.com logo in svg

Komatsu PC500LC-10R, Руководство по ремонту, Страница: 584 / 758

Поделиться
Скачать
Komatsu PC500LC-10R Скачать руководство пользователя страница 584

ADJUST REARVIEW CAMERA ANGLE

METHOD FOR ADJUSTING REAR VIEW CAMERA ANGLE

k

Adjust the camera always before starting the work. You
cannot  secure  the  visibility  and  a  serious  personal  in-
jury  or  death  may  result  if  the  camera  is  not  adjusted
properly.

k

Prepare a scaffold first in order to provide a safe work-
ing  platform  for  the  time  when  adjusting  the  angle  of
the camera.
If you try to work standing on the counterweight, there
is a danger of serious injury or death due to falling off
from the machine.

Adjust the angle of the rearview camera so that people within
approximately 1 m {3ft 3in} away from the machine's rear part
(W) can be seen in the machine monitor at the operator's seat.

If the image on the monitor is not aligned correctly, adjust the
mounting angle (A) of the rearview camera in the following pro-
cedure.
Angle (A) can be adjusted within the range from 32 to 53 °.

ADJUST REARVIEW CAMERA ANGLE

30 TESTING AND ADJUSTING

30-178

PC500LC-10R

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов