Komatsu PC500LC-10R Скачать руководство пользователя страница 574 | Manualshive

Страница: 574 / 758

Komatsu PC500LC-10R Скачать руководство пользователя страница 574

Even if the confirmation screen is displayed and No-Injection
cranking is operated, the function does not become effective in
the following cases. Turn the starting switch OFF once to oper-
ate.

• The communication between the machine monitor and en-

gine controller is not normal.

• An engine start operation has been performed before the

message “No-injection cranking is possible” is displayed.

1.

Select “No-Injection Cranking” on “Service Menu” screen.

REMARK

For selecting method, see “Operating method of service
mode” in “SERVICE MODE”.

2.

When  “No-Injection  Cranking”  screen  is  displayed,  confir-
mation  for  the  execution  of  No-Injection  cranking  is  dis-
played. Select the action with the function switch.
F5:  Does  not  implement  (returns  the  screen  to  “Service

Menu”).

F6: Executes.

3.

If no-injection cranking (no fuel injection on every cylinder)
is enabled, “No-injection cranking is possible. Please turn
the key off after no-injection ends.” is displayed on the
screen. Crank the engine with the starting motor.

NOTICE
Do not crank the engine for 20 seconds or longer to
protect the starting motor.

REMARK

While the screen is changing to the screen as shown in the
figure, the screen of “Getting Ready” is displayed.

4.

After the cranking is completed, turn the starting switch to OFF position.
You cannot change the screen described above to another screen.

KOMTRAX SETTINGS MENU
METHOD FOR CONFIRMING KOMTRAX SETTINGS (TERMINAL STATUS)

On “KOMTRAX setting display” screen, select “Terminal Status” with the function switches or numeral input
switches.
"“Terminal Status”" is used to check the setting condition of the KOMTRAX terminal.

SET AND OPERATE MACHINE MONITOR

30 TESTING AND ADJUSTING

30-168

PC500LC-10R

«
...
572
573
574
575
576
...
»

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов