manualshive.com logo in svg

Komatsu PC500LC-10R, Руководство по ремонту, Страница: 502 / 758

Поделиться
Скачать
Komatsu PC500LC-10R Скачать руководство пользователя страница 502

TEST OIL LEAKAGE

Tools for testing oil leakage

Symbol

Part No.

Part name

Q'ty

Remarks

A

Commercially

available

Measuring cylinder

1

B

07379-01044

Flange

2

Size: 10

C

07376-70522

Plug

1

Size: 4

D

Commercially

available

Plate

1

Size: 250x260x32

E

Commercially

available

Pin

1

Size: φ 200x80

k

Place the machine on a level ground, and then lower the work equipment completely to the ground in
a stable posture. Set the lock lever to LOCK position, and then stop the engine.

k

Parts and oil are still very hot immediately after the engine is stopped. It may cause burn injury. Wait
for the temperature to go down, and then start the work.

Check this item under the following conditions.
Hydraulic oil temperature: 45 to 55 °C
For testing oil leakage to perform troubleshooting, refer to this section.

METHOD FOR TESTING OIL LEAKAGE FROM BOOM CYLINDER

1.

Set the boom cylinder at RAISE stroke end, and stop the engine.

2.

Release the remaining pressure from the piping on the boom cylinder head side by referring to “RELEASE
REMAINING PRESSURE FROM HYDRAULIC SYSTEM”.

REMARK

Operate the lever only with the boom RAISE direction to release the remaining pressure.

3.

Disconnect  the  hose  (1)  on  the  cylinder  head  side  and
block the hose side by using plug C.

k

 Be careful not to disconnect the hose on the cylin-

der bottom side.

4.

Start the engine.

5.

Select and display “Pre-defined Monitoring” (01/11) by re-
ferring to “SET AND OPERATE MACHINE MONITOR”.

6.

Adjust the hydraulic oil temperature so that it is within the
specified range.

7.

Turn the fuel control dial to MAX (High idle) position.

8.

Operate  the  work  equipment  control  lever  to  relieve  the
pressure in the boom RAISE circuit.

k

 Be careful not to operate the lever to “Boom LOWER” side.

9.

30 seconds after the relief is started, measure the oil leakage for 1 minute.
See STANDARD VALUE TABLE, “STANDARD VALUE TABLE FOR MACHINE” for standard values.

Restore the machine after finishing the test.

METHOD FOR TESTING OIL LEAKAGE FROM ARM CYLINDER

1.

Set the arm cylinder at IN stroke end, and stop the engine.

2.

Release the remaining pressure from the piping on the arm cylinder head side by referring to “RELEASE
REMAINING PRESSURE FROM HYDRAULIC SYSTEM”.

TEST OIL LEAKAGE

30 TESTING AND ADJUSTING

30-96

PC500LC-10R

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов