Komatsu PC500LC-10R Скачать руководство пользователя страница 493

Страница: 493 / 758

Adjust the hydraulic oil temperature so that it is within the specified range.

Turn the fuel control dial to MAX (High idle) position.

10. Operate each control lever and switches, and measure the outlet pressure when the solenoid valve is ener-

gized and de-energized.

REMARK

• When the solenoid valve is energized and de-energized, the display of the machine monitor also

changes.

• For the conditions for turning the solenoid valve ON/OFF, see “OPERATING CONDITION OF SOLE-

NOID VALVE”.

See STANDARD VALUE TABLE, “STANDARD VALUE TABLE FOR MACHINE” for standard values.

Remove the testing tools and restore the machine after the test is finished.

OPERATING CONDITION OF SOLENOID VALVE

(1) 2-stage relief solenoid valve operation table

Operating condition of solenoid valve

Operating

state of sole-

noid valve

Overheat 1st setting is ON

OFF (de-ener-

gized)

When overheat 2nd setting is applied

All signals of work equipment, swing, and travel are OFF

Swing lock switch

ON (ener-

gized)

When travel signal is conducted

L mode

When boom lower signal is conducted

P-mode, E-mode

When one-touch power maxi-
mizing switch is turned on

When signals other than swing single
signal are conducted

When swing single signal is conducted

OFF (de-ener-

gized)

Other than the above conditions

(2) Attachment selector solenoid valve operation table (for the attachment installed specification)

Operating condition of solenoid valve

Operating

state of sole-

noid valve

Working mode

Other than B

OFF (de-ener-

gized)

ON (ener-

gized)

(3) Machine push-up solenoid valve operation table

Operating condition of solenoid valve

Operating

state of sole-

noid valve

Machine push-up switch

OFF

ON (ener-

gized)

OFF (de-ener-

gized)

30 TESTING AND ADJUSTING

TEST OUTLET PRESSURE OF SOLENOID VALVE

PC500LC-10R

30-87

Содержание PC500LC-10R






















































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание PC500LC-10R

Отзывы:

Komatsu PC500LC-10R, Руководство по ремонту, Страница: 493 / 758

Результаты поиска

Содержание PC500LC-10R

Отзывы: