manualshive.com logo in svg

Komatsu PC500LC-10R, Руководство по ремонту, Страница: 471 / 758

Поделиться
Скачать
Komatsu PC500LC-10R Скачать руководство пользователя страница 471

3.

Remove the oil pressure pickup plugs (PFC) and (PRC).
(PFC): Front pump discharge pressure pickup port
(PRC): Rear pump discharge pressure pickup port

4.

Install the nipple C in the hydraulic tester A to the position
where the oil pressure pickup plugs (PFC) and (PRC) were
removed.

5.

Connect the gauge A1 of hydraulic tester A to the nipple C.

REMARK

Gauge in the digital hydraulic tester B can also be used in-
stead of the gauge A1.

6.

Start the engine.

7.

Select and display “Pre-defined Monitoring” (01/11) by re-
ferring to “SET AND OPERATE MACHINE MONITOR”.

8.

Adjust the hydraulic oil temperature so that it is within the
specified range.

9.

Set the working mode to P (“Power Mode”).

10. Turn off the auto-deceleration.
11. Turn the fuel control dial to MAX (High idle) position.
12. Check the pump pressure when all control levers and con-

trol pedals are in NEUTRAL position.
The pressure when the unload valve operates is displayed.
See STANDARD VALUE TABLE, “STANDARD VALUE TA-
BLE FOR MACHINE” for standard values.

Remove the testing tools and restore the machine after the test is finished.

METHOD  FOR  TESTING  WORK  EQUIPMENT  RELIEF  PRESSURE  BY  MACHINE
MONITOR

1.

Start the engine.

2.

Select “Pre-defined Monitoring” (04/11) or “Monitoring Se-
lection  Menu”  and  display  the  following  monitoring  items
by  referring  to  “SET  AND  OPERATE  MACHINE  MONI-
TOR”.
Monitoring code: 01100 “Front Pump Pressure”
Monitoring code: 01101 “Rear Pump Pressure”
Monitoring code: 04401 “Hydraulic Oil Temperature”

3.

Adjust the hydraulic oil temperature so that it is within the
specified range.

4.

Set the working mode to P (“Power Mode”).

5.

Turn the swing lock switch to OFF position.

6.

Operate the cylinders to be checked to the stroke end.

REMARK

Turn the secondary work equipment actuation switch to OFF position when oil pressure in boom circuit is
relieved.

7.

Turn the fuel control dial to MAX (High idle) position.

30 TESTING AND ADJUSTING

TEST AND ADJUST OIL PRESSURE IN WORK EQUIPMENT, SWING,

AND TRAVEL CIRCUITS

PC500LC-10R

30-65

Содержание PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов