Komatsu PC45MR-30403 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 475

Komatsu PC45MR-30403 Скачать руководство пользователя страница 39

PRECAUTIONS FOR OPERATION

CHECKS BEFORE OPERATION

If the checks before starting are not performed properly, the machine will be unable to display its full perform-
ance. It is dangerous and may cause serious personal injury or death.
When performing the checks, move the machine to a wide area with no obstructions, and pay careful attention
to the surroundings. Prohibit other personnel from coming close to the machine during checks.

• Fasten the seatbelt. When the brakes are applied sudden-

ly, the operator may be thrown out of the operator's seat. It
is dangerous and may cause personal injury.

• Check that the movement of the machine matches the dis-

play on the control pattern card.
If it does not match, replace it immediately with the correct
control pattern card.

• Check the operating condition of the machine, work equip-

ment, and travel and swing systems.

• Check for any problem in the sound, vibration, heat and

smell of the machine, or abnormalities of instruments. Also
check that there is no leakage of oil or fuel.

• If any problem is found, repair it immediately.

PRECAUTIONS FOR OPERATION

SAFETY

2-28

«
...
37
38
39
40
41
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов