Komatsu PC45MR-30403 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 475

Komatsu PC45MR-30403 Скачать руководство пользователя страница 37

START ENGINE

USE WARNING TAGS

If  there  is  a  "DANGER!  Do  NOT  operate!"  warning  tag  dis-
played,  it  means  that  someone  is  performing  inspection  and
maintenance of the machine. If the warning tag is ignored and
the  machine  is  operated,  the  person  performing  inspection  or
maintenance  may  be  caught  in  the  rotating  parts  or  moving
parts. It is dangerous and may cause serious personal injury or
death. Do not start the engine or touch the levers.

CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE

Perform the following checks before starting the engine at the beginning of the day's work to ensure that there is
no problem with the operation of the machine. If these checks are not performed properly, problems may occur
with the operation of the machine, and there is a danger that may lead to serious personal injury or death.

• Remove all dirt from the surface of the window glass to ensure a good view.
• Be sure to perform thorough walk-around check.
• Remove all dirt from the surface of the lens of the headlamps and working lamps, and check that they light

up correctly.

• Check the coolant level, fuel level, and oil level in engine oil pan, check for clogging of the air cleaner, and

check for damage to the electric wiring.

• Check that there is no mud or dust accumulated around the movable parts of any pedals, and check that

the pedals work properly.

• Adjust the operator's seat to a position where it is easy to perform operations, and check that there is no

damage or wear to the seat belt or mounting clamps.

• Check that the gauges work properly, check the angle of the mirror, and check that the control levers are all

at NEUTRAL position.

• Before starting the engine, check that lock lever (1) is in

LOCK position (L).

• Adjust the mirrors so that the rear of the machine can be

seen easily from the operator's seat.

• Check that there are no people or obstacles above, below,

or in the area around the machine.

• Check that the floor is securely fixed with the floor tilt fixing

bolts. If it is not securely fixed, it may lead to a serious per-
sonal injury or death.

PRECAUTIONS FOR OPERATION

SAFETY

2-26

«
...
35
36
37
38
39
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды