manualshive.com logo in svg

Komatsu PC45MR-30403, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Komatsu PC45MR-30403 Скачать руководство пользователя страница 356

METHOD FOR INSTALLING RUBBER SHOES

1.

Engage the rubber shoe track with the sprocket and place it over the idler.

2.

Rotate  the  sprocket  in  reverse  direction  (A),  push  in  the
rubber shoe track, and stop the rotation.

3.

Insert  the  steel  pipes  (2)  between  the  rubber  shoe  track
and track frame.

4.

Rotate the sprocket in reverse direction (A) again, engage
the rubber shoe track with the idler securely, and then stop
the rotation.

5.

Check that the rubber shoe track is securely engaged with
the sprocket and idler.

6.

Adjust the rubber shoe track tension by referring to “METHOD FOR CHECKING AND ADJUSTING RUB-
BER SHOES TRACK TENSION”.

7.

Check that the rubber shoe track is securely engaged with the sprocket and idler and its tension is correct.

8.

Operate the work equipment control levers, and lower the machine slowly by using the boom and arm.
Operate the levers slowly.

METHOD FOR CHANGING SHOES

k

k

 WARNING

The idler cushion must be removed and adjusted when the steel shoes or road liner are replaced with
the  rubber  shoes,  or  reversely.  Accordingly,  be  sure  to  ask  your  Komatsu  distributor  for  the  replace-
ment.
 

MAINTENANCE

MAINTENANCE PROCEDURE

4-47

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды