background image

PRECAUTIONS FOR OPERATION

PRECAUTIONS FOR JOBSITE

INVESTIGATE AND CONFIRM JOBSITE CONDITIONS

On the jobsite, there are various hidden dangers that may lead to serious personal injury or death. Before start-
ing operations, always check the following to confirm that there is no danger on the jobsite.

• Always  be  careful  when  performing  operations  near  materials  such  as  thatched  roofs,  dry  leaves  or  dry

grass, because they are easily combustible and may cause fire.

• Check the terrain and condition of the ground at the jobsite, and determine the safest method of operation.

Do not operate in a dangerous area where landslides or rockfall may occur.

• If water lines, gas lines, or high-voltage electrical lines may

be buried under the jobsite, contact the management com-
pany to identify their locations, and be careful not to dam-
age any of these lines.

• Take necessary measures to prohibit other personnel from

coming close to the machine during operation.

• In particular, if you need to operate on a road, protect pe-

destrian and cars by designating a person for jobsite traffic
duty or by installing fences around the jobsite.

• When  traveling  or  operating  in  shallow  water  or  on  soft

ground, check the water depth, speed of the current, con-
dition of bedrock, and shape of the ground beforehand. Always avoid any place that will obstruct travel.

PRECAUTIONS WHEN WORKING ON LOOSE GROUND

• Avoid driving or operating the machine near the edge of cliffs, road edges, and deep ditches. The ground

may  be  weak  in  such  areas.  If  the  ground  should  collapse  under  the  weight  or  vibration  of  the  machine,
there is a hazard that the machine may fall or tip over. Remember that the soil is weak in these areas, after
heavy rain or blasting or after earthquakes.

• When working on embankments or near excavated ditches, there is a hazard that the weight and vibration

of  the  machine  will  cause  the  soil  to  collapse.  Before  starting  operations,  take  steps  to  ensure  that  the
ground is safe and to prevent the machine from rolling over or falling.

SAFETY

PRECAUTIONS FOR OPERATION

2-23

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы: