manualshive.com logo in svg

Komatsu PC45MR-30403, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Komatsu PC45MR-30403 Скачать руководство пользователя страница 334

METHOD  FOR  REPLACING  AIR  CLEANER  ELEMENT  ON  MACHINE  EQUIPPED
WITH DOUBLE ELEMENT

1.

Release the hooks (4) and remove the cover (5).

2.

Hold the outer element (6), rock it lightly up and down and
to  the  right  and  left,  and  pull  it  out  while  turning  it  to  the
right or left.
Do not remove the inner element (9) at this time.

3.

When the outer element (6) is removed, check that the in-
ner element does not come out of position and is not at an
angle.
If it is at an angle, push it straight to the bottom with your
hand.

4.

Clean the dust sticking inside the air cleaner body (7) and
on the cover (5) by using a clean cloth or brush.

5.

If any dust is attached to the vacuator valve (8) installed to the cover (5), remove it.

NOTICE

• Do not clean and reuse the inner element.

Replace the inner element with a new one at the same time when the outer element is replaced.

• If the outer element and cover are installed while the inner element is not installed properly, the out-

er element will be damaged.

• The sealing portion of the improper part lacks precision, and allows the entry of dust, which leads

to damage of the engine. Do not use such improper part.

• Be sure to install the air cleaner element facing in the correct direction.

Install so that the bottom of the air cleaner element (a) (face where no hole is drilled) comes to cov-
er (5) end.
If it is installed in wrong direction, it may cause breakage of the air cleaner element or serious dam-
age to the engine.

• When inserting the element into the body, if the rubber at the tip is swollen or the outer element is

not pushed in straight, and cover (5) is installed by force with hook (4), there is a danger that hook
(4) and air cleaner body will be damaged, so be careful when installing.

6.

Remove the inner element (9), and then quickly install the new inner element.
Install the inner element securely so that it does not move.

7.

Push the new outer element in straight with your hand to the air cleaner body (7).
Hold the outer element, and rock it lightly up and down and to the right and left while pushing it in, the ele-
ment can be inserted easily.

MAINTENANCE

MAINTENANCE PROCEDURE

4-25

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды