manualshive.com logo in svg

Komatsu PC45MR-30403, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Komatsu PC45MR-30403 Скачать руководство пользователя страница 319

HANDLE HYDRAULIC COMPONENTS

• The hydraulic system is at high temperature during and just after operation. During operations, it is also un-

der  high  pressure,  so  when  performing  inspection  and  maintenance  of  hydraulic  related  equipment,  be
careful of the following points.

• Stop the machine on a flat ground, lower the bucket to the ground, and perform the work so that there is no

pressure on the cylinder circuits.

• Always stop the engine.
• Immediately after stopping operations, the hydraulic oil and lubricating oil is at high temperature and high

pressure, so wait for the oil temperature to go down before starting maintenance.

• Even after the temperature has gone down, some parts may still be under internal pressure, so when loos-

ening plugs, bolts, or hose connections, do not stand directly in front of the parts, and loosen slowly to re-
lease the internal pressure before removing.

• When performing inspection and maintenance of the hydraulic circuit, always release the air in the hydraulic

tank to remove the internal pressure.

• The inspection and maintenance include check of the hydraulic oil level, replacement of filters, changing of

the hydraulic oil.

• When high-pressure hoses have been removed, check that there is no damage to O-rings. If any damage is

found, replace O-ring.

• When the hydraulic oil filter element or strainer is replaced or cleaned, or when a hydraulic component is

repaired, replaced, or its piping is removed, air in the circuit must be bled.

OUTLINE OF MAINTENANCE

MAINTENANCE

4-10

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды