manualshive.com logo in svg

Komatsu PC45MR-30403, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Komatsu PC45MR-30403 Скачать руководство пользователя страница 295

TROUBLES AND ACTIONS

ACTIONS WHEN RUNNING OUT OF FUEL

When  starting  the  engine  again  after  running  out  of  fuel,  fill  with  fuel,  and  bleed  the  air  from  the  fuel  system
before starting the engine.
Always check the fuel level to prevent running out of fuel.
If the engine has stopped due to run out of fuel, all air must be sufficiently bled from the fuel circuit.

PROCEDURES FOR BLEEDING AIR FROM FUEL CIRCUIT

1.

Pull engine rear cover (1) toward you to open it.
Open  engine  rear  cover  (1)  fully  and  it  is  secured  by  rod
(2).

2.

Pull cooling cover (3) toward you to open it.

3.

Turn rod (4) to LOCK position (L), and fix cooling cover (3)
with the rod.

4.

Open dirt cover (5).
Open  dirt  cover  (5)  fully  and  it  will  be  secured  by  cover
support lever (6).

5.

Fill up the fuel tank with fuel.

TROUBLES AND ACTIONS

OPERATION

3-234

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды