PRECAUTIONS FOR HIGH-TEMPERATURE OIL
To prevent burns from hot oil spurting out or from touching
high-temperature parts when checking or draining the oil, wait
for the oil to cool down to a temperature where the cap or plug
can be touched by hand. Then, loosen the cap or plug slowly to
release the internal pressure and remove the cap or plug.
PRECAUTIONS FOR HIGH-TEMPERATURE PARTS
To prevent burns from touching high-temperature parts, when checking or performing maintenance after stop-
ping engine, check the parts have been cooled down to touch with bare hand before checking or maintenance.
PRECAUTIONS FOR HIGH-PRESSURE OIL
The hydraulic system is always under internal pressure. In addition, the fuel piping is also under internal pres-
sure when the engine is running and immediately after the engine is stopped. When performing inspection or
replacement of the piping or hoses, check that the internal pressure in the circuit has been released. If this is not
done, serious personal injury or death may occur. Always observe the following.
• Do not perform inspection or replacement work with the circuit under pressure.
• If there is any leakage from the piping or hoses, the surrounding area will be wet, so check for cracks in the
piping and hoses and for swelling in the hoses.
When performing inspection, wear protective equipment such as protective eyeglasses and leather gloves.
• High-pressure oil leaking from small holes is dangerous
that may penetrate your skin and cause loss of sight if it
contacts your skin or eyes directly. If a jet of high-pressure
oil hit your skin or eyes, and suffer injury, wash the place
with clean water, and consult a doctor immediately for
medical attention.
PRECAUTIONS FOR HIGH-PRESSURE FUEL
While the engine is running, high-pressure is generated in the engine fuel piping. If you try to disassemble the
piping before the internal pressure is released, serious personal injury or death can result. When performing in-
spection or maintenance of the fuel piping system, stop the engine and wait for at least 30 seconds to allow the
internal pressure to go down before starting the work.
HANDLE HIGH-PRESSURE HOSES AND PIPING
If oil or fuel leaks from high-pressure hoses or piping, it may cause fire or defective operation. It is dangerous
and may cause serious personal injury or death. If the hose or piping mounts are loose or oil or fuel is found to
be leaking from the mount, stop operations and tighten to the specified torque.
If any damaged or deformed hoses or piping are found, consult your Komatsu distributor.
Replace the hose if any of the following problems are found.
• Damaged hose or deformed hydraulic fitting.
• Frayed or cut covering or exposed reinforcement wire layer.
• Covering swollen in places.
• Twisted or crushed movable portion.
PRECAUTIONS FOR MAINTENANCE
SAFETY
2-34
Содержание HD325-8
