Komatsu HB365LC-3 Скачать руководство пользователя страница 481 | Manualshive

Страница: 481 / 506

background image

KomVision

k

k

WARNING

• Physically make sure the adjacent safety around the machine. Do not make sure with just the moni-

tor images.

• The work equipment will always show on the top of the monitor screen, regardless of the direction

of the sprocket. Be aware of the direction of the machine.

KomVision is the CCTV system for Komatsu machines.

PRECAUTIONS WHEN USING KomVision

• If the normal range cannot be confirmed in the confirmation of the camera visibility, it is necessary to adjust

the monitor screen. Ask your Komatsu distributor to perform this work.

• The machine monitor image may not be displayed due to darkness at night or in a tunnel, fog, snow, rain,

cloud of dust, etc.

• Obstacles above the camera of the machine are not displayed. Be careful enough of the work equipment of

a large machine, tree branches, etc. in high positions.

• The guide line is displayed with reference to the flat ground, so the distance of the guide line is not correct

on slopes and uneven ground.

MACHINE MONITOR EQUIPMENT NAME

AA: Standard screen, BB: Check before starting screen, CC: Maintenance time warning screen
(1) Wiper switch
(2) Buzzer cancel switch
(3) Auto-deceleration switch
(4) Hydraulic oil temperature gauge

(5) Hydraulic oil temperature caution lamp
(6) Engine coolant temperature gauge
(7) Engine coolant temperature caution lamp
(8) ECO gauge

ATTACHMENTS AND OPTIONS

KomVision

6-39

«
...
479
480
481
482
483
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HB365LC-3

Бренд: Hitachi Страницы: 31

Бренд: Hitachi Страницы: 14

Бренд: Hitachi Страницы: 16

Бренд: Hitachi Страницы: 20

Бренд: Hitachi Страницы: 41

Бренд: Hitachi Страницы: 34

Бренд: Hitachi Страницы: 31

Бренд: Hitachi Страницы: 61

Бренд: Hitachi Страницы: 41

Бренд: Hitachi Страницы: 230

Бренд: Hitachi Страницы: 255

Бренд: Hitachi Страницы: 384

Бренд: Hitachi Страницы: 477

Бренд: Hitachi Страницы: 502

Бренд: Daewoo Страницы: 96

Бренд: Forankra Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды