manualshive.com logo in svg

Komatsu HB365LC-3, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu HB365LC-3 Скачать руководство пользователя страница 390

The  gas  springs  are  located  at  the  engine  hood  (2  places  on
the right and left).

In the following cases, ask your Komatsu distributor for inspection, repair, and replacement.

• The engine hood is heavy to open.
• Oil or gas is leaking from the gas spring.

METHOD FOR BLEEDING AIR FROM HYDRAULIC CIRCUIT

When starting the engine, see “METHOD FOR STARTING ENGINE (3-177)”. If necessary, see the sections for
starting the engine, and moving/steering/stopping the machine in OPERATION.

METHOD FOR BLEEDING AIR FROM PUMP

NOTICE
If the drain hose is installed first, oil will spurt out from the bleeder (1) hole.
If the pump is operated without filling the pump case with hydraulic oil, abnormal heat will be generated
and this may cause a premature damage to the pump.

1.

Loosen the air bleeders (1) (2 places) and check that oil oozes out from the air bleeder.

2.

If the oil does not ooze out, remove the drain hose (2) from
the hydraulic pump case and fill the pump case completely
with hydraulic oil through the drain port.
Oil will come out when the drain hose is removed, so se-
cure  the  hose  fitting  at  a  position  higher  than  the  level  of
the oil in the hydraulic tank.

3.

After completing the air bleeding operation, tighten the air
bleeders (1) and install the drain hose.

METHOD FOR STARTING ENGINE

Start the engine according to “METHOD FOR STARTING ENGINE (3-177)” and run it at low idle for 10 minutes,
and then start the following work.

METHOD FOR BLEEDING AIR FROM CYLINDER

NOTICE
If the engine runs at high speed immediately after startup or a cylinder is operated to its stroke end, air
taken inside the cylinder may cause damage to the piston packing.

1.

Start the engine.

2.

Turn the fuel control dial to Low idle (MIN) position.

3.

Move each cylinder to approximately 100 mm before the stroke end, and repeat the operation 4 to 5 times.
Take care not to move the cylinder to the stroke end.

4.

Turn the fuel control dial to High idle (MAX) position.

5.

Move each cylinder to approximately 100 mm before the stroke end, and repeat the operation 4 to 5 times.
Take care not to move the cylinder to the stroke end.

6.

Turn the fuel control dial to Low idle (MIN) position.

MAINTENANCE PROCEDURE

MAINTENANCE

4-42

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды