Komatsu HB365LC-3 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 506

Komatsu HB365LC-3 Скачать руководство пользователя страница 138

SWITCH DISPLAY/NON-DISPLAY OF ECO GAUGE

It is possible to change the setting of Display/Non-display of
ECO gauge (7).

1.

Select the ECO Gauge Display (8) from the Configurations
screen, then press the switch F6.

2.

ECO Gauge Display setting screen appears.
ON: Displays the ECO gauge (7) on the standard screen.
OFF: Does not display ECO gauge (7) on the standard

screen.

On this setting screen, it is possible to perform the following op-
erations with switches F3 to F6.
F3: Moves to the next item (1 line below). When it is on the last

line, it moves to the first line.

F4: Moves to the previous item (1 line above). When it is on the

first line, it moves to the last line.

F5: Cancels the setting change and returns the screen to the

Configurations screen.

F6: Changes the setting and returns the screen to the Configu-

rations screen.

SET TARGET FUEL CONSUMPTION VALUE DISPLAYED IN ECO GAUGE

It is possible to change the target fuel consumption value (the upper limit value of the green range) of the ECO
gauge .
1.

Select the target fuel consumption value displayed in the
ECO Gauge Target Value (9) from the Configurations
screen, then press switch F6.

2.

ECO Gauge Display Fuel Target Value appears.

EXPLANATION OF COMPONENTS

OPERATION

3-66

«
...
136
137
138
139
140
...
»

Содержание HB365LC-3



























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды