Komatsu D155AX-8E0 Скачать руководство пользователя страница 116

Страница: 116 / 420

Gear

shifting

Ripper raise

operation

Ripper tilt back operation

Each operation while ripper auto-return function is

Steering

Blade
operation

Ripper lift

Ripper tilt

FORWARD Auto-return does

not operate.
(Normal manual
operation is pos-
sible.)

Auto-return does not oper-
ate.
(Normal manual operation is
possible.)

NEUTRAL

REVERSE

Auto-raise opera-
tion

Normal
operation

Operation
(*1)

(*1): Ripper auto-return stops if manual operation is performed.

FUNCTION SWITCHES

The operation of the function switches in the standard screen

CAMERA IMAGE SELECTOR SWITCH

On the standard screen, press switch F3 to switch to the cam-
era image display.

• On machines not equipped with a camera, the guidance

icon related to switch F3 is not displayed.
Even if switch F3 is pressed, the screen will not switch to
the camera image display.

EXPLANATION OF COMPONENTS

OPERATION

3-54

Содержание D155AX-8E0




































































































































































































































































































































































































































Результаты поиска

Содержание D155AX-8E0

Отзывы:

Бренды по названию

Популярные бренды

Komatsu D155AX-8E0, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание D155AX-8E0

Отзывы:

Бренды по названию

Популярные бренды