Komatsu A31001 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 376

background image

intelligent Machine Control SYSTEM

CONTROL BOX

k

k

WARNING

• Do not operate the control box during the operation of the work equipment in order to prevent unex-

pected accident from occurring. Also, do not gaze the control box during performing the work.

• The image of the machine displayed on the control box is only a representation. The image dis-

played on the control box is not enough to ensure the safety around the machine. Check around the
machine with your own eyes.

Control box is the monitor to display the necessary information for the intelligent Machine Control. Various set-
tings are performed on this monitor by inputting data into the touch panel.

(A) Front face of control box
(B) Back face of control box
(1) Touch panel type control box
(2) Internal battery state LED
(3) External power supply state LED
(4) Auto/manual switch
(5) Power button
(6) Reset button

(7) USB port (for uploading and downloading the data

by USB flash drive)

(8) Spare USB port (for mouse connection as needed)
(9) Ethernet connection port
(10) Connector port 1
(11) Connector port 2
(12) Control box fixing joint

Touch panel

This machine uses an electrostatic capacity type touch panel. When operating touch panels with hands wearing
gloves, the reaction becomes degraded.

EXPLANATION OF COMPONENTS

OPERATION

3-20

«
...
36
37
38
39
40
...
»

Содержание A31001

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A31001

Бренд: Agrison Страницы: 83

Бренд: Barreto Страницы: 19

Бренд: Wacker Neuson Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды