Komatsu A31001 Скачать руководство пользователя страница 229 | Manualshive

Страница: 229 / 376

background image

Tap “Brightness Adjustment” button on “Display Options”
screen, the screen changes to Brightness Adjustment screen.

METHOD FOR ADJUSTING BRIGHTNESS ADJUSTMENT SCREEN

Adjust the brightness.

(1): Tap this button to decrease the brightness.
Tap this button and the number of green indicators (4) decreas-
es, and the screen becomes dark.
(2): Tap this button to increase the brightness.
Tap this button and the number of green indicators (4) increas-
es, and the screen becomes bright.
(3): With this button, you can return the brightness in Day and
Night to the default value.
For the default value in Day and Night, refer the position of
mark (5) on the green indicator (4).

SETTING

CONTROL BOX

7-113

«
...
227
228
229
230
231
...
»

Содержание A31001

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A31001

Бренд: Hyundai Страницы: 41

Бренд: Cambridge Elevating Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды