Komatsu A31001 Скачать руководство пользователя страница 207 | Manualshive

Страница: 207 / 376

background image

SECTION VIEW SETTINGS CONTENTS

“Surface Names”
You can display Surface Names.
“Bucket Name”
You can display Bucket Name.

For the items explained below, by putting a tick in the check box, “Display” is set. If a tick is not put, “Non-dis-
play” is set.

SETTING ITEMS BY LEFT TAB

You can perform the display setting for the leftmost position information of the bucket edge.
“Elevation left edge”
You can perform the display setting for Elevation of the bucket
edge (leftmost).
“cut left edge”
You  can  perform  the  display  setting  for  the  distance  from  the
bucket edge (leftmost) to the Surface.
“Offset to line”
You  can  perform  the  display  setting  for  the  distance  from  the
bucket edge to the Alignment.
“Stationing”
You  can  perform  the  display  setting  for  the  distance  from  the
bucket edge to the Stationing.
“Bucket slope”
You can perform the display setting for the inclination of the bucket edge (lateral direction of machine) against
Alignment.

SETTING ITEMS BY CENTER TAB

You can perform the display setting for the center position information of the bucket edge.

SETTING

CONTROL BOX

7-91

«
...
205
206
207
208
209
...
»

Содержание A31001

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A31001

Бренд: Komatsu Страницы: 9

Galeo PC1250-7 Backhoe

Бренд: Komatsu Страницы: 9

Бренд: Komatsu Страницы: 61

Бренд: Komatsu Страницы: 61

Бренд: Eurotrac Страницы: 131

Бренд: IHIMER Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды