Komatsu A31001 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 376

background image

2.

The screen changes to the screen for inputting Project File
name. Input the file name to be created newly, and tap
“OK” button.

3.

The file name of the newly created Project File is added to
the Project Files list.

4.

Tap RETURN button to return the screen to the previous
screen.

METHOD FOR CREATING NEW PROJECT FILE FROM CURRENTLY SELECTED
FILE

You can create the new Project File based on the data of the currently selected Project File.
The name of the currently selected Project File is displayed in “Preload data from current project file:”.
1.

Put a tick to the following item on “New Project” screen.
“Control points, localization, MM-GPS data”

SETTING

CONTROL BOX

7-7

«
...
121
122
123
124
125
...
»

Содержание A31001

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A31001

Бренд: Komatsu Страницы: 522

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды