Kollmorgen AKD-x00306 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 34

background image

2.1 About this Manual

This manual,

AKD SynqNet Communication

, describes the installation, setup, range of functions, and soft-

ware protocol for the SynqNet AKD product series. All AKD SynqNet drives have built-in SynqNet func-
tionality; therefore, an additional option card is not required.

A digital version of this manual (pdf format) is available on the disk included with your drive. Manual updates
can be downloaded from the Kollmorgen website.

Related documents for the AKD series include:

l

AKD Installation Manual This manual provides instructions for installation and drive setup.

l

AKD WorkBench Online Help. This help system describes how to use your drive in common applic-
ations. It also provides tips for maximizing your system performance with the AKD. The Online Help
includes the Parameter and Command Reference Guide which provides documentation for the para-
meters and commands used to program the AKD.

l

Accessories Manual. This manual provides documentation for accessories like cables and regen res-
istors used with AKD. Regional versions of this manual exist.

2.2 Target Group

This manual addresses personnel with the following qualifications:

l

Installation: only by electrically qualified personnel.

l

Setup: only by qualified personnel with extensive knowledge of electrical engineering
and drive technology

l

Programming: software developers, project-planners

The qualified personnel must know and observe the following standards:

l

ISO 12100, IEC 60364 and IEC 60664

l

National accident prevention regulations

During operation there are deadly hazards, with the possibility of death, severe injury or material damage.
The operator must ensure that the safety instructions in this manual are followed. The operator must ensure
that all personnel responsible for working with the servo drive have read and understand the manual.

AKD SynqNet | 2 General

Kollmorgen | kdn.kollmorgen.com | October 2020

5

«
...
3
4
5
6
7
...
»

Содержание AKD-x00306



































Отзывы:

Нет отзывов

Похожие инструкции для AKD-x00306

Бренд: O&K Antriebstechnik Страницы: 118

ADAP-KOOL AKD 102

Бренд: Danfoss Страницы: 130

Бренд: Brasiltec Страницы: 75

Бренд: WEG Страницы: 94

JA comfort SMI series

Бренд: elero Страницы: 6

Бренд: Vicon Страницы: 7

iPOS80x0 BX-CAN

Бренд: Technosoft Страницы: 41

iPOS3602 HX-CAN

Бренд: Technosoft Страницы: 41

Бренд: Technosoft Страницы: 54

Бренд: IBM Страницы: 54

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 122

Бренд: Parker Automation Страницы: 362

VLT PROFINET MCA 120

Бренд: Danfoss Страницы: 8

Бренд: KEB Страницы: 138

Бренд: Parker Страницы: 99

Бренд: Raymarine Страницы: 22

Бренд: VEM Страницы: 4

WriteMaster SE-W164C

Бренд: Samsung Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды