KOJA Future S Скачать руководство пользователя страница 8

Страница: 8 / 41

FUTURE® S AIR HANDLING UNIT

OPERATION AND MAINTENANCE

INSTRUCTIONS

15 December 2020

Ver 1.7 (We reserve the right to changes without prior notice)

CAUTION

The fan models are not designed to be disassembled.

CAUTION

If the fan has to be replaced, the faulty fan is to be returned with a length of the wire
attached to the motor.

CAUTION

If the units have been in storage for an extended time, make sure that there is no moisture
in the link boxes of the motors.

1.4.1 CE marking

Future® S ventilation units are CE marked. The CE mark is attached to the machine plate on the switchboard

door. The manufacturer’s declaration of conformity and other documents relating to the safety of the unit

sections are supplied with the unit.

The ventilation system’s supplier and person responsible for taking the system into use must ensure that the

essential requirements relating to the safety of the unit are complied with and that the equipment

manufacturer’s instructions are followed. Electrical installations and their installation inspections and

measurements must be performed in accordance with standards SFS-EN 60204-1 and SFS 6000-6, and the

person responsible for taking the unit into use must compile the testing and installation documents.

1.4.2 Fire

In case of fire in the unit, do not use water, but a powder extinguisher or such. The materials used in the unit

do not produce harmful amounts of any hazardous gases when burning.

Содержание Future S










































Результаты поиска

Содержание Future S

Отзывы:

Бренды по названию

Популярные бренды

KOJA Future S, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Future S

Отзывы:

Бренды по названию

Популярные бренды