Kohler SFGLD360 Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 314

background image

PRODUCT INFORMATION

INDEX

DATE

Dep. 2

IO-C-M-25-003e A

June 2013

KOHLER 180/240/360/480/560 ENGINES

CENTRIFUGAL OIL FILTER MAINTENANCE INSTRUCTIONS

1/1

1. CLEANING OF FILTER

After stopping the engine completely or isolating the filter from the
lubrication system by means of a valve:

1.1.

Release and remove the clamp (1).

1.2.

Remove the cover and check the top bearing for damage or

wear. Inspect the O-ring (2) and replace it if necessary.

1.3.

Lift the rotor unit and allow oil to flow through the nozzles,

before separating the rotor from the filter body. Secure the filter
body and undo the rotor nut (3). Separate the cover from the rotor
body and dismantle the central support tube (4-5).

1.4.

If there is a sheet of paper at the bottom of the rotor, remove it,

since it contains accumulated impurities. If there is no sheet of
paper, remove sludge from the rotor inside with a wooden spatula
or an adequate wooden object and clean the interior of the rotor
with a cloth. Put a new filtering paper (7).

1.5.

Clean the nozzle with a bronze wire to verify that oil can

circulate freely. Make sure that the inside of the shaft is
unobstructed by impurities. Check the shaft bearings for damage
and excessive wear. Inspect the O-ring (6) for good condition and
replace it if necessary.

1.6.

Clean and wash the central support tube and make sure the

filter holes are unobstructed.

1.7.

Re-assemble the whole rotor and torque the nut (3) to 9.5 to

10.8 Nm (1 to 1.10 kgm).

1.8.

Check the bottom bearings fitted in the filter body for damage

or wear.

1.9.

Remove the cap of the shutoff valve (8) and take out the unit.

Check the spring and valve for damage and freedom of motion.
Inspect the seal (9) and replace it if found damaged.

1.10.

Re-assemble the shutoff valve unit.

1.11.

Re-assemble the whole filter and check for free rotation of the

rotor unit. Then, put the filter cover and secure it with the clamp.

1.12.

With the filter in service, check for possible leaks at seals and

fittings.

Fig. 1 -

Centrifugal filter

Fig. 2 -

Exploded

5.2.11

O&M_2.002211.810_A_10_2016

«
...
247
248
249
250
251
...
»

Содержание SFGLD360



























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SFGLD360

Бренд: Man Страницы: 64

Бренд: Sesame Motor Страницы: 4

Бренд: ZF Страницы: 80

dunkermotoren D258

Бренд: Ametek Страницы: 8

Бренд: Champion Страницы: 72

Бренд: Louvolite Страницы: 4

Бренд: HAMPTON BAY Страницы: 17

Бренд: Honda Страницы: 50

Бренд: HIOTH TECHNOLOGY Страницы: 5

Бренд: Technosoft Страницы: 34

Бренд: STEYR Страницы: 118

Бренд: Honda Страницы: 30

Бренд: Honda Страницы: 41

Бренд: Briggs & Stratton Страницы: 10

Бренд: E-FLITE Страницы: 3

Power 25 Brushless Outrunner

Бренд: E-FLITE Страницы: 4

MINI SWIFT 60CC - USA

Бренд: IAME Страницы: 32

Бренд: Daihatsu Страницы: 294

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды