B
C
CAUTION: Risk of personal injury.
These products are not designed or
intended for use as a grab bar or support bar. Do not install any of these
products in any area where they are likely to be used inadvertently as a
grab bar or support bar.
Kohler Co.
Record your model number: __________________________
1521913-T2-
A
1
1
2
3
4
5
6
7
8
9
10
1521913-T2
All information is based on the latest product information available at the
time of publication. Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important
information.
NOTE:
These products should be located and mounted on a wall. While
they can be mounted to any surface, the best results will come from a stud,
concrete, or drywall mounted product.
INSTALLATION INSTRUCTIONS
TP HOLDER (W/ TRAY)
K-29233T-**/K-29234T-**/ K-29237T-**/ K-29247T-**
DOUBLE TP HOLDER (W/ TRAY)
K-29235T-**/K-29236T-**/ K-29246T-**/ K-29248T-**/ K-29249T-**
Follow all local plumbing and building codes.
1.
Recommended Toilet Paper Holder location.
2A
.
For Double-Post TP Holders (K-29235T/K-29236T/K-29249T)
, verify that
the provided template aligns with your product.
3A. For TP Holders (K-29233T/K-29234T/K-29235T/K-29236T),
loosen the
setscrew(s) and remove the wall mounting bracket from the TP Holder Assy.
4. Uninstall the Mounting Brackets of TP Holder (K-29249T).
4A.
Loosen the setscrew(s) and remove the bonnet(s) from the TP Holder
Assy.
4B.
Loosen the center screw(s) and remove the wall mounting bracket(s) from
the bonnet(s).
5A. For Single-Post TP Holders (K-29233T/K-29234T),
position the wall
mounting bracket on the wall and mark the holes. Ensure that the holes are
vertically levelled.
5B. For Double-Post TP Holders (K-29235T/K-29236T/K-29249T)
, use the
provided template to mark the holes. Verify that the template and marked
holes are levelled.
6A. For TP Holders (K-29237T/K-29246T/K-29247T/K-29248T),
position
the TP Holder Assy on the wall and ensure that the mounting bracket is
horizontally levelled.
6B. For Single TP Holders (K-29237T/K-29247T),
mark the two holes on the
wall.
6C. For Double TP Holders (K-29246T/K-29248T),
mark the four holes on the
wall.
7
. Choose a drill bit according to the surface on which the product is being
installed.
Drill diameter 3 mm holes to install on stud, 6 mm holes for concrete wall and
8 mm holes for drywall.
8.
No plugs are required, when mounted to a wood-panel wall.
8A
.
Installation of concrete wall anchors:
Install wall anchors into the hole
and tap with hammer until it flush with the wall.
8B
.
Installation of butterfly anchors to drywall:
Hold the butterfly anchor and fold the edges inside.
Insert the butterfly anchor into the drilled hole.
Stretch it with pin and tap with hammer until it flush with the wall.
9. For TP Holders (K-29233T/K-29234T/K-29235T/K-29236T/K-29249T),
position the wall mounting bracket on the wall. Use the screws provided in
the accessory kit and secure the wall mounting bracket(s) to the wall.
10
.
For TP Holders (K-29233T/K-29234T/K-29235T/K-29236T),
slide the TP
Holder Assy onto the mounting bracket(S), tighten the setscrew(s) and secure
the TP Holder Assy to the wall.
