Kohler CURTIS 3401T Скачать руководство пользователя страница 25

Страница: 25 / 62

2 — USING THE 3401T

pg. 19

Curtis Model 3401T – August 2022

The Warning and Low gauges flash when they are active. If the BDI percentage is too low, lift lockout
is activated and the icon displays.

Speedometer

The speedometer displays the speed in km/h or mph, depending upon how the device is

configured. The speedometer on the reach trucks and order pickers screen may also display a

speed limit. The following figures show how the preset user interfaces display the speedometer:

Figure 2-3

Speedometer —

Counterbalanced

Forklifts

10.2

km/h

Figure 2-4

Speedometer —

Reach Trucks and

Order Pickers

10.2

km/h

(MAX 20.0)

Hour Meters, Cargo Weight and Lift Height

The hour meters, cargo weight and lift height area displays up to two of the following items at any

given time:

Icon

Hour Meter

00186.9

Pump controller hour meter

00122.8

Traction controller hour meter

001234

Cargo weight

010.500

Lift height

These indicators may be displayed in any combination, such as the combinations in the

following examples:

00122.8

00186.9

010.500

00122.8

010.500

001234

00122.8

Содержание CURTIS 3401T































































Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Бренды по названию

Популярные бренды

Kohler CURTIS 3401T, Руководство пользователя

Результаты поиска

Содержание CURTIS 3401T

Отзывы:

Бренды по названию

Популярные бренды