USER S GUIDE
Working Status Flushing
Deodorizing Flushing
Flushing Volume
When the water pressure or flush amount exceeds a certain
limit, take off the cover and turn the adjusting bolt clockwise
with hex pan to a proper place.
Manual Flushing
Normal working status, approach the supplied special magnetic
stick (flushing control stick) to the right part of the sensor lens.
The system is now at a manual status and the indicator will flash
every 1 seconds. Approach the flushing control stick to the right
part of the sensor lens once, it ll flush once. The maximum flush
time is approximately 30 seconds. This status will last for
about 8 minutes until turns to the normal working status.
If the flushing control stick keeps near to the
sensing window for 30 seconds, the manual
status will be terminated automatically and
reassume the normal working status.
NOTE:
Adjustment Bolt
调节栓
Flushing Control Stick
,
,
在正常工作模式下，用配备的专用磁棒（冲洗控制棒）靠近
感应窗口右侧位置，此时系统进入手控状态，感应指示灯每
1
秒闪烁一次。用冲洗控制棒每靠近感应窗口右侧一次，小
便器即放水冲洗一次，冲水最长时间约为
30
秒。此状态维持
约
8
分钟。结束后转为正常工作状态。
当水压过大或冲水量偏大时
,
取下面板
,
使用六角扳手顺时
针方向调节水量调节栓至适量即可改善冲水量
。
接通电源
10
秒后即可进入工作状态。
当连续有人使用时，小便器每
2
分钟自动冲洗一次。
If the urinal is used continuously, the urinal will flush every
2 minutes automatically.
The urinal enters into working status after the power is
connected for 10 seconds.
使用说明
工作状态
防臭冲洗
水流量
手控冲洗
注意：冲洗控制棒如持续超过
30
秒一直不离开感应窗口，
将自动解除手控冲洗状态回复到正常工作状态。
冲洗控制棒
PSD ECO 0.5&1L flush mode change
The default flush mode of sensor is 0.5L , you can switch to
the 1L flush mode with flushing control stick. Operate as
follow: after initial power on, during the time of the indicator
flashing, you can switch the flush mode by putting the flushing
control stick near the right part of the sensor lens. There will
be twice quick rinse after you complete the 1L flush mode
setting. If you need to reset the 0.5L flush mode, you can cut
off the power completely and restart the sensor, during the
time of the indicator flashing, you're able to switch flush mode
with flushing control stick, there will be once quick rinse after
you complete the 0.5L flush mode setting.
NOTE:
just for 8881T-VC01-BN/AF(PSD ECO 0.5&1L /DC)
、
8881T-VC03-BN/AF(PSD ECO 0.5&1L /AC)
0.5L
和
1L
可调式冲洗模式切换
:
产品出厂默认设置为
0.5L
冲洗模式，可以使用冲洗控制棒将产品
设置为
1L
冲洗模式。具体操作方法如下：产品初始上电，在指示
灯显示长亮的时间内，用配备的专用磁棒（冲洗控制棒）靠近感
应窗口右侧位置切换冲洗模式。设置
1L
冲洗模式成功后，会有连
续
2
次快速冲洗。若需切换回
0.5L
冲洗模式，可侧底断电后重新上
电，在指示灯显示长亮的时间内使用磁棒设置，设置
0.5L
冲洗模
式成功后，会有一次快速冲洗。
注：
仅适用于
8881T-VC01-BN/AF(
0.5L&1L
可调式
/
直流型
)
、
8881T-VC03-BN/AF(
0.5L&1L
可调式
/
交流型
)
10
1206437-T01-A