Kodak DryView 8150 Скачать руководство пользователя страница 69

Страница: 69 / 178

Operation and Maintenance

October 4, 2004

7F3319

2-35

Setup Local Panel Screen

From this screen you can access several other screens that allow you to
adjust some of the Local Panel properties.
To display this screen:

Menu

Setup Imager

Local Panel

Calibrate touch accuracy -

Displays a screen for setting the accuracy of

the touch buttons on the Local Panel. Requires the Service passcode.

Touch Beep Duration

- Displays a screen for setting the duration of the

"beep" that sounds when any button is touched. Requires a Key Operator
passcode. Refer to

“Adjust Touch Beep Duration” on page 2-61

Backlight intensity

- Displays a screen for setting the intensity of the

Local Panel backlight. Requires a Key Operator passcode. Refer to

“Adjust

Backlight Intensity” on page 2-62

Audible alarm

- Displays a screen from which you can:

• Enable or disable the audible alarm.
• Set the duration of audible alarm tone pulses.
The audible alarm sounds when the number of Jobs Waiting for Media goes
from 0 to 1 or when an

Error Message

screen is displayed. Requires a

Key Operator passcode. Refer to

“Adjust the Audible Alarm” on page 2-63

Passcodes

- Displays a screen for entering and editing passcodes

Requires the Service passcode. Refer to

“Local Panel Passcodes” on

page 2-57

Содержание DryView 8150



















































































































































































Результаты поиска

Содержание DryView 8150

Отзывы:

Kodak DryView 8150, Руководство пользователя, Страница: 69 / 178

Результаты поиска

Содержание DryView 8150

Отзывы: