Kodak DryView 8150 Скачать руководство пользователя страница 48

Страница: 48 / 178

2-14

7F3319

October 4, 2004

Operation and Maintenance

Home Screen Status Line

The following messages can appear on the Status Line:

Message

Explanation

Printing

Printing images from the print queue.

Ready

Ready to print. No images in the print queue for
the currently loaded film size.

Self-test

The Imager is performing the power-up self test.

Warming =

The Imager is warming up. The number of
minutes until the Imager will be at operating
temperature is displayed after the = sign. The
Imager can receive images but not print until
fully warmed.

Door open requested The operator has touched the

Door Open

button on the Local Panel. The door will be
unlatched after the Imager closes the film
cartridge and completes any films currently
being processed.

Door open

The front door is open.

Hood open

The hood is open.

Not ready

The Imager cannot print.

Printing disabled

Printing has been disabled for service.

Содержание DryView 8150



















































































































































































Результаты поиска

Содержание DryView 8150

Отзывы:

Похожие инструкции для DryView 8150

Бренды по названию

Популярные бренды

Kodak DryView 8150, Руководство пользователя

Результаты поиска

Содержание DryView 8150

Отзывы:

Похожие инструкции для DryView 8150

Бренды по названию

Популярные бренды