kobi NET-KOBI-IP-16CH Скачать руководство пользователя

Страница: 95 / 181

Figure 7. 19

Export Finished

Check backup result.

Note:

The Player player.exe will be exported automatically during record file export.

Figure 7. 20

Checkup of Event Export Result Using USB Flash Drive

7.1.4

Backing up Video Clips

Purpose:

You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB
HDDs, USB writer) or SATA writer.

Steps:

Enter Playback interface.

Please refer to

Chapter 6.1 Playing Back Record Files.

During playback, use buttons and

in the playback toolbar to start or stop clipping record file(s).

Quit Playback interface after finishing clipping and you will then be prompted to save the clips.

Note:

A maximum of 30 clips can be selected for each channel.

Содержание NET-KOBI-IP-16CH






















































































































































































Результаты поиска

Содержание NET-KOBI-IP-16CH

Отзывы:

Похожие инструкции для NET-KOBI-IP-16CH

Бренды по названию

Популярные бренды

kobi NET-KOBI-IP-16CH, Руководство пользователя

Результаты поиска

Содержание NET-KOBI-IP-16CH

Отзывы:

Похожие инструкции для NET-KOBI-IP-16CH

Бренды по названию

Популярные бренды