Kobelco SK135SR-7 Скачать руководство пользователя страница 336 | Manualshive

Страница: 336 / 412

background image

5-8

［

］

5.2.2

FIXING THE MACHINE

• Retract the radio antenna in before transportation. In addition, remove the mirrors if required. Store the removed

parts securely in the cab.

• Place a wood block under the bucket (attachment) link to avoid contacting the ground and protect the bucket

cylinder from being damaged during transportation.

After loading the machine on the required position, fix the machine by the following procedures.

CRAWLER

1.

Check that all guards and doors are locked.

2.

Chock the front and rear of the crawlers and fix the
machine securely with wire ropes of appropriate
strength to prevent the body from moving back and
forth or rolling by vibration of the trailer. In addition,
secure individual parts and removed parts securely
on the trailer.

RUBBER CRAWLER AND PAD SHOE

2

2

1

1.

Check that all guards and doors are locked.

2.

Chock the front and rear of the crawlers and fix the
machine securely with wire ropes of appropriate
strength to prevent the body from moving back and
forth or rolling by the vibration of the trailer. In
addition, secure individual parts and removed parts
securely on the trailer.
Do not directly apply the wire rope (1) on the rubber
crawler or the pad shoe. Place pads (2) (such as
soft cloth) at the left and right of the crawler frame to
fix the rope securely on the loading platform of the
truck.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
334
335
336
337
338
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Takeuchi Страницы: 182

Бренд: JACK RABBIT Страницы: 18

Бренд: RAM Страницы: 52

Бренд: Eurotrac Страницы: 131

Бренд: VMB Страницы: 14

Бренд: VMB Страницы: 27

Бренд: Hyundai Страницы: 415

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды