Kobelco SK135SR-7 Скачать руководство пользователя | Manualshive

Страница: 312 / 412

background image

4-80

［

INSPECTION AND MAINTENANCE

4.18.2

REPLACING AIR BREATHER ELEMENT

Immediately after engine operation, the oil is hot and it may cause in burns. Wait until the oil temperature cools
down before attempting to change the element.

• To keep the hydraulic oil clean and to extend the service life of the hydraulic components, replace the filter

element at regular intervals.

• Every 1000 hours replacement is a rough guideline. If the machine is operated in very sandy and dusty

conditions, replace the oil filter earlier than the specified interval.

1.

Move the machine to a level and firm place.

2.

Put the bucket on the ground.

3.

Stop the engine and move the pilot control shut-off lever to the "LOCKED" position.

1

4.

Remove breather cap (1) on the top of the hydraulic
oil tank and keep pressing the valve until the
pressure inside the hydraulic oil tank is released.

1

2
3
4

5

6

7

5.

After removing breather cap (1), remove seal (2),
nut (3) and seal (4) in order.

6.

Turn cover (5) in the counterclockwise direction,
remove the cover, and then remove element (6).

7.

Install new element (6) and install cover (5) aligning
the groove.

8.

Be sure to prevent water and dirt from entering the
air intake and exhaust ports between cover (5) and
body (7).

9.

Attach seal (4) on top of cover (5), then attach nut
(3) and set seal (2).

To avoid breakage of bolts, do not over-tighten nut (3).
Tightening Torque: 10 to 14 N·m (7.4 to 10.3 lbf·ft)

10. Securely tighten breather cap (1) clockwise by hand.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
310
311
312
313
314
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Komatsu Страницы: 261

Бренд: Savaria Страницы: 16

Бренд: Savaria Страницы: 16

Бренд: Savaria Страницы: 24

Бренд: Savaria Страницы: 60

Бренд: Wacker Neuson Страницы: 292

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды