Kobelco SK135SR-7 Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 412

background image

3-34

［

MACHINE OPERATION

］

3.10.2

TRAVEL PROCEDURES

ABOUT TRAVELING

• Confirm the travel motor position before traveling. When the travel motor is positioned at the front side, the

machine moves reversely to travel lever operations.
The normal travel control can be performed when the travel motor is at the rear side of the machine and the front
idler is at the front side of the machine.

• Sound the horn to warn the workers in the working site.

ABOUT TRAVEL SPEED

During traveling, do not change the travel speed. Also, the travel speed should be set to the LOW (1st) speed when
the machine is traveling on a downhill, or being loaded to/unloaded from a trailer. A sudden change of the machine
stability could cause personal injury.

F

R

N

Before starting traveling operation move the control lock
lever to "UNLOCKED position" and set the bucket at the
height of 30 to 40 cm (12 to 16 inch) above the ground.

F: Forward traveling

N: Neutral (Stop)

R: Backward traveling

Forward/Reverse traveling

•

Push (forward) or pull (backward) both the left and
right travel levers simultaneously.
Both the forward and reverse travel speed can be
changed by lever displacement.

Copyright©2020 Kobelco Construction Machinery Co.,Ltd. All rights reserved. [S2YY00041ZE03] [0701CsCshWbYs]

«
...
214
215
216
217
218
...
»

Содержание SK135SR-7





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SK135SR-7

Бренд: Takeuchi Страницы: 17

Бренд: Hitachi Страницы: 31

Бренд: Hitachi Страницы: 281

Бренд: Hitachi Страницы: 306

Бренд: Hitachi Страницы: 442

Бренд: New Holland Страницы: 6

GOlfinho SPORTS PANDAPOOL

Бренд: WFA Страницы: 6

Бренд: Garbin Страницы: 72

Бренд: ZIEHL-ABEGG Страницы: 12

PC600-8 BACKHOE

Бренд: Komatsu Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды