background image

Multi station

Multi station

Art. No. : 23066REGHE

Operating instructions

1 Safety instructions

Electrical devices may only be mounted and connected by electrically skilled
persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

For parallel connection of several motors to an output it is essential to observe the
corresponding instructions of the manufacturers, and to use a cut-off relay if necessary.
The motors may be destroyed.

Use only venetian blind motors with mechanical or electronic limit switches. Check the
limit switches for correct adjustment. Observe the specifications of the motor
manufacturers. Device can be damaged.

Danger of electric shock on the SELV/PELV installation. Do not connect loads for mains
voltage and SELV/PELV together on a single switch actuator.

These instructions are an integral part of the product, and must remain with the end
customer.

2 Device components

Figure 1

(1) Keypad for local control
(2) Programming button and LEDs
(3) Bus connection
(4) Input terminals
(5) Status LED
(6) Output terminals

1/7

82596803
j0082596803

26.01.2017

Содержание JUNG 23066REGHE








Отзывы: