Connecting Infrared:
Infrared receivers and emitters can be
connected on either side. Please note 12 volt power for the infrared is
supplied only on the HDMI send or HDMI receive that has the PS1205
power supply connected. Emitters should be connected using a Knoll
infrared connection block (IR55) or using an inline (series) 220 ohm
dropping resistor to avoid early emitter failure.
HDMI Balun Specifications:
Models and Dimensions
UDR-HDMI (in-wall Decora™ version): 4.1"h x 1.4" w x 2.0"d.
UDS-HDMI (in-wall Decora™ version): 4.1"h x 1.4" w x 2.0"d.
UR-HDMI (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).
US-HDMI (black enclosure): 1.1"h x 2.6"w x 2.8"d (28 x 66 x 71 mm).
Inputs and Outputs
:
Send Unit: One HDMI input jack, two RJ-45 out-jacks, one-DC
power input, one three position Infrared connector.
Receive Unit: One HDMI output jack, two RJ-45 in-jacks, one-DC
power input, one three position Infrared connector.
Power:
Send Unit: 12 VDC 500mA.
Receive Unit: 12 VDC 500mA.
Warranty
Knoll Systems warrants its products sold in the USA and Canada by authorized
Knoll dealers to be free of defects in materials and workmanship. This warranty
extends for three full years from the date of purchase by the original consumer.
Any products returned to Knoll Systems and found to be defective by Knoll
Systems within the warranty period will be repaired or replaced at Knoll Systems
option, at no charge. Knoll Systems will not be responsible for the actual cost of
installation or removal of the product, nor for any incidental or consequential
damages. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you. This
warranty gives you specific legal rights. You may have additional legal rights
that vary from state to state.
Knoll HDMI baluns pass HDCP signals and does not manipulate
them in any way.
Knoll Systems www.knollsystems.com
145 Tyee Drive Point Roberts, WA 98281
12140 Horseshoe Way, Richmond BC V7A 4V5
Tel. (604) 272 4555, fax (604) 272 5595
Made in Canada Knoll Systems All Rights Reserved
UDR-HDMI Receiver
UDS-HDMI Sender
UR-HDMI Receiver
US-HDMI Sender
Installation Instructions v1.7
Warning
: To be installed and/or used in accordance with
appropriate electrical codes and regulations.
If you are not sure
about any part of these instructions, consult a qualified
electrician.
Caution
: Do not install this product in an electrical junction box
with 110V or higher unless an approved barrier separates the
high and low voltage sections.
Introduction:
Thank you for your purchase of a Knoll active
balun system. This system is specifically designed to send HDMI
and infrared signals safely down a two cat 5e or cat 6 wires up
to 115 feet (35 meters) without encountering signal degradation
problems (resolutions lower than 1080p will go further).
To install wires inside walls, in most jurisdictions require wires
to be minimum class 2 rated for safety. Almost all conventional
HDMI wires are unrated so they cannot legally be installed
inside walls. The most cost effective method to install a legal
HDMI inwall run is to use cat 5e wire and Knoll HDMI baluns.
Features:
Tabletop box design or Decora™ style available.
Will safely send 480i/p, 720p and 1080i/p signals.
PS1205 power supply can be connected on either the
send or receive side.
Mix and match decora style and tabletop style.
Infrared receivers and emitters can be connected on
either side