Knick SensoGate WA131MH Скачать руководство пользователя

Страница: 33 / 60

SensoGate WA131MH

6.3.4 Immersion Tube: Removal

01.

Remove the drive unit

(1)

➜

Drive Unit: Disassembly, p. 31

02.

Move the drive unit

(1)

to the PROCESS position (sensor must be mounted).

➜

Moving into the PROCESS Position, p. 23

03.

Loosen the screws

(2)

around 4 rotations using a screwdriver of type TX25

(3)

(do not completely

unscrew).

04.

Rotate the immersion tube

(4)

around 60° counterclockwise until the bayonet coupling of the im-

mersion tube

(4)

is open.

05.

Pull the immersion tube

(4)

off the sensor

(6)

✓

The O-ring

(5)

is now visible, or it may be located in the removed immersion tube

(4)

06.

Check the O-ring

(5)

for damage; replace the O-ring

(5)

if necessary.

➜

Gasket Sets, p. 40

Содержание SensoGate WA131MH





























































Результаты поиска

Содержание SensoGate WA131MH

Отзывы:

Похожие инструкции для SensoGate WA131MH

Бренды по названию

Популярные бренды

Knick SensoGate WA131MH, Руководство пользователя

Результаты поиска

Содержание SensoGate WA131MH

Отзывы:

Похожие инструкции для SensoGate WA131MH

Бренды по названию

Популярные бренды