manualshive.com logo in svg

Knick SensoGate WA131M, Руководство пользователя

Поделиться
Скачать
Knick SensoGate WA131M Скачать руководство пользователя страница 43

SensoGate WA131M

43

7.2  Retractable Fitting: Emergency Release

WARNING! Process or rinse medium, possibly containing hazardous substances, can escape

from the SensoGate WA131M or the process port. 

Follow the safety instructions. 

➜

Safety, p. 5

 

WARNING! The emergency release deactivates the safeguard “Immersion lock without

mounted sensor” (the lock in SERVICE or PROCESS position is not affected). 

Reset the emergency

release after successful troubleshooting. 

Note: 

An emergency release may be necessary in the event of a fault in the locking function, e.g., if the

safety lock button cannot be depressed in any position.

1)

1

2

3

4

5

WARNING! Pressurized process medium may escape from the process port. 

Loosen the cou-

pling nut of the process connection a maximum of one full turn. 

01.

Loosen the c

oupling nut 

(2)

 a maximum of one full turn until the recess 

(3)

 is underneath the set

scr

ew 

(4)

. 

➜

Drive Unit: Disassembly, p. 36

02.

Using the Allen wr

ench A/F 2.5 mm 

(1)

, screw in the set scr

ew 

(4)

 up to the stop.

03.

Move the SensoGate WA131M into the SER

VICE position. 

➜

Moving into the SERVICE Position, p. 26

04.

Perform troubleshooting; as required, send the SensoGate WA131M to Knick for repair.

➜

Malfunction States, p. 42

Note: 

The function of the safeguard “Immersion lock without a mounted sensor” is only assured if the

set screw 

(4)

 is correctly installed.

05.

Unscrew the set scr

ew 

(4)

 using the Allen wr

ench A/F 2.5 mm 

(1)

 until the set scr

ew 

(4)

 lies flush

with the outer face of the drive unit.

06.

Fasten the c

oupling nut 

(2)

 

➜

Drive Unit: Assembly, p. 37

07.

As required, check the function of the “Immersion lock without a mounted sensor”.

➜

Immersion Lock Without a Mounted Solid-Electrolyte Sensor: Functional Test, p. 33

➜

Immersion Lock Without a Mounted Liquid-Electrolyte Sensor: Functional Test, p. 34

1)

On versions with the safeguard “Immersion lock without a mounted sensor”, the safety lock button cannot be de-
pressed if the sensor is not mounted. 

➜

Safeguards, p. 6

Содержание SensoGate WA131M

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды