manualshive.com logo in svg

Knick SensoGate WA131M, Руководство пользователя

Поделиться
Скачать
Knick SensoGate WA131M Скачать руководство пользователя страница 35

SensoGate WA131M

35

6.2  Preventive Maintenance

6.2.1  Approved Lubricants

Application

Pharma and food

Chemicals and wastewater

Lubricant

B

eruglide L 

1)

(silicone-free)

Par

aliq GTE 703 

2)

(containing silicone)

Syn

theso Glep 1

(silicone-free)

Elastomer seal materials
FKM

-

-

+

FFKM

-

-

+

EPDM

-

-

+

FKM – FDA

+

+

-

FFKM – FDA

+

+

-

EPDM – FDA

+

+

-

Note: 

Lubricant Par

aliq GTE 703 c

ontains silicone and has good lubricating properties even at elevated

temperatures and with numerous travel movements. Par

aliq GTE 703 is a special applica

tion and used

at the customer's express request.

6.2.2  Characteristics of Process-Wetted Materials

Note: 

The stated values are reference values and provide general information. Concentrations of acids

or alkalis, temperatures, mechanical effects, and the duration of the effect impact the materials to a
greater or lesser degree. Therefore, no guarantee is given for the stated values. A pretest is recom-
mended for cases where there has been no prior experience using the material in the process. Mix-
tures of substances constitute a prime example.

M

echanical 

str

ength

Temper

atur

e

resistanc

e

Resistanc

e 

to acids

Resistanc

e 

to alk

alis

Resistanc

e t

o

salt solutions

Resistanc

e t

o

cleaning agen

ts

or solv

en

ts

Stainless steel material no. 1.4571

1

1

3 

3)

2

3

2

Hastelloy C-22 material no. 2.4602

1

1

2

1

1

1

PEEK (carbon fiber-reinforced)

1

1

2 

4)

1

1

2

PVDF (carbon fiber-reinforced)

2

2

2 

5)

2

1

2

PP (carbon fiber-reinforced)

3

4 

6)

3 

7)

3

2

2

Titanium Grade 2 material no. 3.7035

1

1

2

1

1

1

1 = very well suited

5 = unsuitable

See also

➜

Product Code, p. 12

1)

FDA compliant, NSF-H1 registered

2)

FDA compliant, USDA H1 registered

3)

Not resistant to hydrochloric or sulfuric acid

4)

Not resistant to highly oxidizing media (concentrated sulfuric acid, nitric acid or hydrogen fluoride)

5)

Not resistant to ketones, amines, fuming sulfuric and nitric acid

6)

M

ax. 80 °C / 176 °F

7)

Not resistant to highly oxidizing media (e.g., nitric acid, chromic acid or halogens)

Содержание SensoGate WA131M

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды