Knick SensoGate WA 132 Series Скачать руководство пользователя

Страница: 40 / 48

Accessories / Spare Parts

SensoGate WA 132

ZU 0680

SensoGate Service Set, Basic

These tools are suitable for minor maintenance operations. They

help separating the drive unit from the process adaptation and

replacing the immersion tube including sensor gasket maintenance.

ZU 0647

Sensor Mounting Wrench

Required for safely screwing in the sensor without overloading the

PG 13.5 plastic thread of the sensor head by an excessive torque

(as caused by an open-end wrench).

ZU 0670/1,

Air Supply for Pressurized Sensors

0.5 – 4 bar

ZU 0670/2,

Air Supply for Pressurized Sensors

1 – 7 bar
This module maintains the defined overpressure in the pressure

chamber of the sensor.

ZU 0713

Hose, 20 m (extension for ZU 0670

)

ZU 0759

Protective Cap

The ZU 0759 protective cap protects against intrusion of liquids or

particles into the area of the electrical connector of a sensor

(e.g., due to weather exposure during outdoor use).

Note:

Can only be used with fittings for solid-electrolyte sensors.

ZU 0742

Adapter for Free Hose Connection,

with electrical limit switches, PEEK housing

This adapter is used for operating the SensoGate WA 132 via multi-

plug without the Unical 9000 (X) controller and the corresponding

media connection.

For ordering, use the part numbers beginning with

, e.g., ZU 0680.

Содержание SensoGate WA 132 Series

















































Результаты поиска

Содержание SensoGate WA 132 Series

Отзывы:

Похожие инструкции для SensoGate WA 132 Series

Бренды по названию

Популярные бренды

Knick SensoGate WA 132 Series, Руководство пользователя

Результаты поиска

Содержание SensoGate WA 132 Series

Отзывы:

Похожие инструкции для SensoGate WA 132 Series

Бренды по названию

Популярные бренды