Knick SensoGate WA 132 Series Скачать руководство пользователя

Страница: 36 / 48

Specifications

SensoGate WA 132

Permissible process pressure and

temperature

6 bar (at 0 ... 40 °C)
6 bar (40 °C), falling linearly to 3 bar (100 °C)
3 bar (max. 1 hour) at 135 °C

Ambient temperature

-10 ... +70 °C

Ingress protection

IP 66

Housing material

Stainless steel / PP or PEEK

Permissible pressure for probe control

4 ... 7 bar

Quality of compressed air

Standard

According to ISO 8573-1:2001

Quality class

3.3.3 or 3.4.3

Solid contaminants

3 (max. 5 μm, max. 5 mg/m

)

Water content for temperatures > 15 °C

Class 4, pressure dew point 3 °C or below

Water content for temperatures 5 ... 15 °C Class 3, pressure dew point -20 °C or below
Oil content

Class 3 (max. 1 mg/m

)

Sensors

with solid electrolyte

Ø 12 mm, length 225 mm, PG 13.5 thread

with liquid electrolyte

Ø 12 mm, length 250 mm

Process adaptations

Flanges, EN 1092-1

DN 32 to DN 100

Flanges, ANSI B 16.5

1½" to 3"

Flange bushings, suitable for

sight glass fittings acc. to DIN 3237 Part 2

from DN 40

Connections

Inlet

Via Unical multiplug

Outlet

PFA hose coupling for hose, Ø 8 × 1 mm

for pressurized sensors

Hose connection NW 6 mm, pressure in calibration

chamber 0.5...1 bar above process pressure (max. 7 bar)

for compressed air

Via Unical multiplug (control air for retractable fitting)

Immersion depths / Dimensions

See dimension drawings

Process-wetted materials

PEEK (natural)

Specifications for application in hazardous locations

N° of EU Type Examination Certificate

KEMA 04 ATEX 4035X

Device

SensoGate WA 13** - X … retractable fitting

ATEX marking of the equipment

Compressed air:

4 to 7 bar

Rinsing water:

max. 7 bar

Tamb

Made in Germany

-10 to 70 °C

Retractable probe / Drive unit

Type

No.

KEMA07ATEX 0065

II 1 G/D c II

No self-heating

For temp specs see manual

14163 Berlin

SensoGate®

SensoGate

Compressed air:

4 to 7 bar

Rinsing water:

max. 7 bar

Tamb

Made in Germany

-10 to 70 °C

Drive unit

0044

Made in Germany

For Ex specs see drive unit

KEMA 07 ATEX 0065

SensoGate®

Type

No.

Insertion fitting

Antrieb

Schilder

WA130-N*, WA130-X*,

WA132-N*, WA132-X*

Prozess

nicht Ex

0044

Ambient temperature (Ex)

-10 ... +70 °C

Process pressure (Ex)

Max. 6 bar

Compressed-air supply (Ex)

4 to 7 bar, momentarily approx. 100 l / min

Process temperature (Ex)

0 to 120 °C (plastic) or 0 to 140 °C (steel)

Special conditions (Ex)

None

Explosive atmospheres caused by gases, vapors, mists:

The maximum surface temperature only depends on the process temperature at the SensoGate housing and the flange.

II 1 G Ex h IIC T6 ... T3 Ga

II 1 D Ex h IIIC T80°C ... 140°C Da

Содержание SensoGate WA 132 Series

















































Результаты поиска

Содержание SensoGate WA 132 Series

Отзывы:

Похожие инструкции для SensoGate WA 132 Series

Бренды по названию

Популярные бренды

Knick SensoGate WA 132 Series, Руководство пользователя

Результаты поиска

Содержание SensoGate WA 132 Series

Отзывы:

Похожие инструкции для SensoGate WA 132 Series

Бренды по названию

Популярные бренды