Knick Protos LDO 3400-170 Скачать руководство пользователя страница 36

Страница: 36 / 64

Menu Display

Maintenance

Opening the Maintenance Menu

From the measuring mode:

Press

menu

key to select menu.

Select Maintenance (maint) using

arrow keys, press

enter

to confirm.

Passcode 2958 (The passcode can be

edited by the administrator.)

Then select "Sensor SE 740".

Sensor Monitor

You can use the sensor monitor to

validate the sensor by immersing

it in a solution with known oxygen

concentration, for example, and then

checking the values measured.

Menu selection

Return to meas

25.6°C

Select:

[enter]

Lingua

83.3 %Air

Maintenance

Sensor monitor, autoclaving counter

Note:

Function check (HOLD) mode active (Setting: BASE module)

Sensor SE 740

25.6°C

83.3 %Air

Sensor monitor

Autoclaving counter

Maintenance

25.6°C

83.3 %Air

Sensor SE 740

Module LDO 3400-170

Module BASE 3400-029

Sensor SE 740

25.6°C

83.3 %Air

Sensor monitor

Autoclaving counter

Autoclaving Counter

After having completed an auto-

claving process, you must manually

increment the autoclaving count.

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos LDO 3400-170

































































Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды

Knick Protos LDO 3400-170, Руководство пользователя

Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды